MENU BAR

Minggu, 22 April 2012

Memperbaiki Motherboard yang Rusak(Fixing a Damaged Motherboard )



Papan induk (motherboard) adalah papan sirkuit tempat berbagai komponen elektronik saling terhubung seperti microprocessor dan memory (RAM, ROM, BIOS) beserta chip kontroler lainnya dan biasa disingkat dengan kata mobo.
Oke Langsung aza ya! gejala dan cara mengatasi motherboard yang rusak :
Mati Total
Periksa power supply: Dalam keadaan kabel power di lepas dari power supply, lepaskan socket kabel Atx1 yang terpasang pada Mainboard. Setelah terlepas, pasangkan kembali kabel power, sambungkan/shortkan kabel berwarna hijau dengan kabel berwarna hitam, periksa apakah kipas di power supply berputar? Kalau berputar berarti power supply bagus. Lepas kembali kabel sambungan tadi dan pasang kembali kabel Atx1 ke motherboard.
Periksa Jumper Clear CMOS, apakah di posisi Clear atau Free, biasanya kalau motherboard baru, posisi jumper CMOS ada pada posisi Clear.
Periksa IC Chipset dalam keadaan tersambung dan di Switch On, apakah panasnya berlebih atau tidak, over heat berarti Chipset tersebut sudah rusak. Untuk part IC CMOS sampai saat ini tidak dijual bebas.
Periksa juga apakah switch on nya berfungsi.
Bongkar Motherboard tersebut secara hati-hati, coba anda bersihkan pakai tiner, kalau bisa gunakan tiner botol jangan yang di kaleng. Setelah bersih anda keringkan.
Ganti IC regulator yang terletak disekitar soket Power Atx di motherboard.
Ganti Elko yang kapasitasnya 1000 s/d 3300 uf / 10 Volt yang terletak disekitar soket power Atx di motherboard. Hati-hati untuk bongkar pasang komponen pastikan kabel power jangan tersambung ke listrik.
Nyala Tapi Tidak Tampil
Coba anda perhatikan dan dengarkan apakah ada bunyi atau suara bip. Kalau ada, kerusakan biasanya ada di processor, memory dan VGA.
Periksa Processor, coba anda pegang pendinginnya apakah panasnya berlebih atau dingin? Kalau panas berlebih berarti kipas processor tidak bekerja dengan baik maka anda ganti, tapi kalau dingin berarti processor tidak bekerja alias rusak.
Periksa memory, biasanya kalau memory rusak terdengar suara bip pada speaker sebanyak 3 kali. Dalam keadaan mati, cabut memory bersihkan pinnya menggunakan penghapus pensil sampai bersih, kemudian pasang kembali. Kalau masih rusak berarti ada salah satu IC nya yang rusak.
Periksa VGA Card, cabut VGA Card, dalam keadaan mati / off coba anda tekan, ada kemungkinan kurang masuk atau coba anda bersihkan kaki / pin nya. Jika VGA card menggunakan kipas, bersihkan kipas tersebut.
Kalau masih tidak tampil coba anda periksa jangan-jangan monitornya yang tidak nyala, untuk memastikannya yang rusak monitor atau CPU, coba anda tekan tuts Numlock pada keyboard, apakah lampu Numlock-nya nyala atau tidak. Kalau nyala berarti kerusakan pada CPU.
Yang menjadi standar saya kalau memperbaiki Komputer, saya selalu membersihkannya dari debu, apakah itu motherboard, memory, cdrom, floppy disk, dll, karena hal tersebut sangat berpengaruh apa lagi kalau komputernya dalam keadaan kotor / lama tidak dibersihkan. Tapi anda harus hati-hati dalam pengerjaannya dan jangan terburu-buru.

Hang Dan Sering Mati / Merestart (Reset) Sendiri
Periksa Power Supply, coba pakai power supply yang lain apakah masih me-restart sendiri atau hang. Kalau setelah diganti power supply ternyata normal/ bagus, berarti power supply ada masalah. Ganti saja karena kalaupun bisa diperbaiki saya sendiri kurang yakin apakah masih bisa berfungsi dengan baik, karena power supply merupakan komponen yang sangat vital. Apalagi untuk saat ini harga power supply sanggat murah, saya sarankan ganti saja.
Periksa apakah ada virusnya, program anti virus harus selalu terpasang dan aktifkan auto protect nya. Saya biasa memakai Norton Anti virus. Anda harus sering meng-update antivirus anda karena bila ada virus varian baru, anti virus anda akan mendetect sekaligus menghilangkan virusnya.
Pada saat hang dan ada pesan blue screen seperti “eror vxd at address…”, biasanya ada masalah di memory. Bersihkan memory tersebut seperti langkah diatas.
Coba anda install ulang Windows.
Kalau masih hang / me-restart sendiri coba anda periksa di motherboard, anda perhatikan perubahan fisik komponen terutama elko/kapasitor, yang bentuknya bulat hitam ada tulisan kapasitasnya antara 1000 uf/10Volt s/d 3300 uf/10 volt, biasanya terlihat, kalau yang rusak terlihat kembung / bengkak dan mengeluarkan cairan atau karat.
CMOS Checksum Failure (Baterai Low)
Gejala kerusakan & Solusinya :
Muncul pesan CMOS failure (Kerusakan pada baterai CMOS, ganti baterai tersebut)
Seting tanggal, time dan konfigurasi lain di BIOS berubah (Setelah baterai diganti, lakukan setting ulang pada BIOS).

















  
 
The main board (motherboard) is the circuit board where a variety of interconnected electronic components such as microprocessors and memory (RAM, ROM, BIOS) chip along with other controllers and commonly abbreviated to mobo said.
Jump aza Okay yes! symptoms and how to cope with a damaged motherboard:
The total dead
Check the power supply: In the state of the power cord from the power supply off, disconnect the cable Atx1 socket mounted on the Mainboard. Once detached, attach the power cable, plug / cable shortkan green, black cables, check that the power supply fan spinning? If the spin is a good power supply. Back off the extension cord and plug it back before cable Atx1 to the motherboard.
Check the Clear CMOS Jumper, whether in position or Free Clear, usually when a new motherboard, CMOS jumper position on Clear position.
Check the IC Chipset plugged in and on the Switch On, if excess heat or not, over-heat means the chipset is already damaged. For CMOS IC part to date not sold freely.
Also check whether the switch on its functioning.
Motherboard dismantle it carefully, you try to wear clean thinners, if you can not use thinners bottle is in the can. After you dry clean.
Replace the regulator IC which is located around the ATX power socket on the motherboard.
Replace the capacity Elko 1000 s / d 3300 uf / 10 Volt, located around the ATX power socket on the motherboard. Carefully dismantled components to make sure the power cord is not connected to electricity.
Flame But Not Shown
Try to look and listen if there is sound or beep sound. If there is, there is usually damage the processor, memory and VGA.
Check Processor, you try to hold refrigeration if excess heat or cold? If it means overheating the processor fan is not working properly then you will change, but if the cold means the processor does not work broken alias.
Check your memory, if memory is usually broken voice on the speaker beep 3 times. Is off, remove the pin clean memory using a pencil eraser to clean, then reinstall. If it means there's still broken one of his damaged IC.
Check your VGA card, unplug the VGA Card, in the dead / off you try to press, there is less chance enter or try to wash the feet / her pin. If the VGA card using the fan, clean the fan.
If it still does not appear, do not you try to check the monitor is not a flame, to make sure that broken monitor or CPU, you try to press keys on the keyboard Numlock, whether the NumLock light a flame or not. If the flame is damage to the CPU.
Is the standard when repairing my computer, I always clean out the dust, whether it be the motherboard, memory, cdrom, floppy disk, etc., because it is so what else could affect the computer in a dirty / old are not cleaned. But you have to be careful in the process and do not rush.

Hang And Often Off / Restart (Reset) Himself
Check the Power Supply, try another power supply if it still restarts itself or hangs.If after the power supply was replaced by normal / good, power supply means there is a problem. Replace it if it can be fixed myself was not sure whether I can still function properly, because the power supply is a vital component. Especially for the current price sanggat cheap power supply, I suggest changing it.
Check if there is virus, anti-virus program should always be installed and enable auto protect. I used to use Norton Anti virus. You have to frequently update your antivirus because if there is a new variant virus, anti virus you will eliminate the virus mendetect.
At the time hang and blue screen messages such as "vxd error at address ...", there is usually a problem in memory. Clean the memory is like a step above.
Try to reinstall Windows.
If it still hangs / restarts itself trying to check on the motherboard, you notice the physical changes of components primarily Elko / capacitor, there is a black round writing in capacity between 1000 uf/10Volt s / d 3300 uf/10 volt, usually seen, if the damaged looks bloated / swollen and leak or rust.
CMOS Checksum Failure (Battery Low)
Symptoms of damage & Solutions:
CMOS failure message appears (The damage to the CMOS battery, replace battery)
Setting the date, time and other configurations in the BIOS to change (After replacing the battery, did reset the BIOS settings).


http://ari-berbagi.blogspot.com/

0 komentar:

Posting Komentar

Popular Posts

Categories

About

About Me

Foto saya
KESEJAHTERAAN MULTIMEDIA E
Powered By Blogger
Diberdayakan oleh Blogger.

Square Banner